MASCO Catalog: Concrete Forming & Accessories

89 MASONS SUPPLY COMPANY Oregon (800) 537-3407 ♦ Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Hillsboro | Medford | Portland | Salem | Ridgefield | Seattle | Tacoma | Woodinville M A S C O . N E T SNAPTIES TIEING/HANDSET INFORMATION Cone Removal Wrench This “tee” handled wrench utilizes a lag screw thread for easy insertion and removal of snaptie cones which failed to remove themselves along with the tie end. Concrete Plug Concrete plugs are designed to be used with 1" x 1" snaptie cones. Break or twist snap-tie end off the cured wall. Apply with plastic applicator bottle into void. For a cleaner finish, dip the end of a concrete cone into the adhesive solution to avoid drips. Then simply push the cone firmly into the void. Adhesive holds instantly and fully cures within 15 minutes. Sand flat if protruding.Concrete plugs are preferred over patching due to less labor and the elimination of possible patch shrinkage. How to Break Back Wrench Head Ties: 1. Keep the tension on the tie and bracket. 2. Place a 3/8", 6 point socket and ratchet over the head of the tie. 3. Standing in front of the tie, hold the socket on the hex head with one hand and turn the ratchet with the other. A 1/4 to 1/2 turn of the ratchet will normally break the tie end. 4. Mason's cannot guarantee that ends longer than 4-3/4" will breakback consistently. No. Description Wt (lbs) Qty/Ctn DS 1CONPL Flush 0.03 500 DS 1CONR Reveal 0.02 2,000 No. Wt (lbs) DS 44245 1.0 SWL provides a factor of safety of approximately 2 to 1. Snap-Coil ™ Tie A multipurpose tie for job-built form systems. Standard button head snap tie on one end and a 1/2" coil rod adapter on the other. Snaps off like normal tie. A low cost solution for one-sided forming and adjustable-length ties. Welded to rigorous standards using computer-controlled equipment: each tie is as strong as a standard snaptie. Standard 2250 lbs Safe Working Load. Just like Loop-Coil Ties, Snap-Coil Ties can be used with 1/2" coil rod to make adjustable ties or to anchor into existing walls for one- sided walls. Here, Snap-Coil Ties are used to form a one-sided, battered wall. The ties are threaded onto 1/2" coil rod stubs welded onto vertical sections of steel pipes left from previous grouting operation. For about the cost of a single coil tie, the ties give you the adjustability of a coil tie with the convenience of a disposable snap-tie end. Eliminates the labor and expense of coil bolts or other removable components. Supplied with standard 1" cones and 1" breakback. Available in 4-3/4" end (SC-64) or 8-1/4" end (SC-68). Like all Transition Ties, the ties can also be used for making adjustable-length ties or used with Rebar Hooks for Stay-Form blind side walls and other applications. 100 pieces per carton. No. Size SWL Tension (lbs) Min 1 side Wall Wt (lbs) SD SC64 4-3/4" end 2,250 6-1/4" .29 SD SC68 8-1/4" end 2,250 6-1/4" .33 SD SC44 4-3/4" end 2,250 4-1/4" .24 SD SC48 8-1/4" end 2,250 4-1/4" .38 ¾" 1" 1" ⅜ " FLUSH REVEAL 1" ¼ " ½ " ⅜ " 1 " Min. One-Sided Wall Setback Accepts ½” coil rod 1” plastic cone Standard button-head snap tie end Snap Tie Tail Length Adjustment range