MASCO Catalog: Concrete Forming & Accessories

86 MASONS SUPPLY COMPANY Oregon (800) 537-3407 ♦ Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Hillsboro | Medford | Portland | Salem | Ridgefield | Seattle | Tacoma | Woodinville M A S C O . N E T TIEING/HANDSET SWL provides a factor of safety of approximately 2 to 1. SNAPTIES Optional Waterseal Washer Optional Waterseal Washers provide a tight fitting 3/4" diameter neoprene washer located near the center of the tie. This helps eliminate water seepage along the tie by breaking the surface continuity of the wire. Available on request. Standard Plastic Cone (PC) Standard Snapties are manufactured from medium high carbon wire and 1"x1" plastic spreader cone providing a nominal 1" breakback. 1-3/16" end uses 3/4" plywood and wedge. 1-5/8" end uses 1-1/8" plywood and wedge. 4-3/4" end uses 3/4" plywood, 2x4 walers and wedge. 5-1/8" end uses 1-1/8" plywood, 2x4 walers and wedge. 8-1/4" end uses 3/4" plywood, 2x4 walers, 2x4 strongback for formwork alignment and wedge. Special ends available on request. Standard Snapties provide a safe working load of 2,250 lbs. Adequate end clamps are required to develop safe working loads.100 pieces per carton. Wrench Head The six sided snaptie is produced with a high quality, uniform shaped hot forged head. This six sided head permits break back of ties while the formwork is still in place. The tie uses a 1"x1" plastic cone to provide a nominal 1" break back. Use a 6 point 1/2" socket wrench to break back. After ties are broke-off, then the forms can easily be removed which greatly increases the speed of stripping resulting in significant labor savings. Masons cannot guarantee that ends longer than 4-3/4" will consistently breakback. Standard Snapties provide a safe working load of 2,250 lbs. Adequate end clamps are required to develop safe working loads.100 pieces per carton. Plastic cones Plastic Cones are recommended when specifications require a nominal 1" or 1-1/2" breakback. Plastic cone sizes other than listed are available on special order. WALL THICKNESS BREAKBACK LUMBER AND WEDGE LUMBER AND WEDGE No. Size Wt/Ctn (lbs) CT 61316PC 6" x 1-3/16" 22.5 CT 6158PC 6" x 1-5/8" 22.5 CT 6SE 6" x 4-3/4" 23.5 CT 65PC 6" x 5-1/8" 25.0 CT 6LE 6" x 8-1/4" 32.0 CT 81316PC 8" x 1-3/16" 25.0 CT 8158PC 8" x 1-5/8" 25.0 CT 8SE 8" x 4-3/4" 26.0 CT 85PC 8" x 5-1/8" 27.0 CT 8LE 8" x 8-1/4" 34.0 CT 101316PC 10" x 1-3/16" 30.0 CT 10158PC 10" x 1-5/8" 30.0 CT 10SE 10" x 4-3/4" 28.0 CT 105PC 10" x 5-1/8" 29.0 CT 10LE 10" x 8-1/4" 37.0 CT 121316PC 12" x 1-3/16" 30.0 CT 12158PC 12" x 1-5/8" 30.0 CT 12SE 12" x 4-3/4" 31.0 CT 125PC 12" x 5-1/8" 32.0 CT 12LE 12" x 8-1/4" 39.0 MST 14SE 14" x 4-3/4" 33.0 MST 14LE 14" x 8-1/4" 41.0 MST 16SE 16" x 4-3/4" 35.0 MST 16LE 16" x 8-1/4" 43.0 MST 18SE 16" x 4-3/4" 38.0 MST 18LE 18" x 8-1/4" 46.0 MST 20SE 20" x 4-3/4" 40.0 MST 20LE 20" x 8-1/4" 48.0 MST 22SE 22" x 4-3/4" 42.0 MST 22LE 22" x 8-1/4" 50.0 MST 24SE 24" x 4-3/4" 44.0 MST 24LE 24" x 8-1/4" 53.0 MST 30SE 30" x 4-3/4" 51.0 MST 30LE 30" x 8-1/4" 59.0 MST 36SE 36" x 4-3/4" 58.0 MST 36LE 36" x 8-1/4" 66.0 Other sizes available on request. No. Size Wt/Ctn (lbs) CFT 6SE 6" x 4-3/4" 24.0 CFT 8SE 8" x 4-3/4 26.0 CFT 10SE 10" x 4-3/4" 28.0 CFT 12SE 12" x 4-3/4" 31.0 CFT 6LE 6" x 8-1/4" 32.0 CFT 8LE 8" x 8-1/4" 34.0 CFT 10LE 10" x 8-1/4" 37.0 CFT 12LE 12" x 8-1/4" 39.0 Other sizes available on request. No. Diameter Size Length Wt (lbs) MFG 1CONE 1" 1" .09 MFG 114CONE 1-1/4" 1-1/2" .018