MASCO Catalog: Concrete Forming & Accessories

159 MASONS SUPPLY COMPANY Oregon (800) 537-3407 ♦ Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Hillsboro | Medford | Portland | Salem | Ridgefield | Seattle | Tacoma | Woodinville M A S C O . N E T Straight Ferrule Loop The Ferrule Loop Insert is manufactured by welding a wire loop to a steel ferrule which has been machined from bar stock. One end of the ferrule is closed, while the other end is drilled and tapped to accept an NC threaded bolt. Typically, this insert is used to attach a precast wall panel to a building frame, as well as provide attachment of other structural elements that may be required. Thin Slab NC (Wing Insert) The Flared Thin Slab Insert was designed for use in thin precast concrete elements or for conditions where a longer insert cannot be used. This insert is closed at the back end of the ferrule to keep concrete from getting into the threads. The ferrule will accept only NC threaded bolts of appropriate diameters. Open Coil Insert N/C Thread The Expanded Coil Ferrule Inserts were developed as a more effective means for increasing the insert's tensile capacity, without increasing its depth of embedment. By increasing the width of the base, the volume of the resisting shear cone is significantly increased. The expanded pitch coils welded to the more deeply embedded end of the insert serve to distribute the applied loads over a larger volume of concrete. Available in longer lengths, as required. Minimum spacing between inserts is twice the corner spacing. SWL is based on 1/2" set back from face of concrete SWL provides a factor of safety of approximately 3 to 1 in 3,000 psi normal weight concrete. Consult manufactures data on values on shear and reduced edge distance. Not for use as a lifting insert. Note: Masons Supply does not recommend 1/2" diameter bolts for lifting/handling of precast concrete. No. Size Wire SWL Tension (lbs) Min. Edge Distance Wt (lbs) CFI FLS124 1/2" x 4-1/8" .223 3,000 9" .25 CFI FLS126 1/2" x 6-1/8" .306 4,000 9" .38 CFI FLS584 5/8" x 4-1/8" .223 3,000 9" .35 CFI FLS586 5/8" x 6-1/8" .306 5,000 11" .48 CFI FLS344 3/4" x 4-1/8" .223 3,000 9" .54 CFI FLS346 3/4" x 6-1/8" .306 5,000 11" .67 CFI FLS786 7/8" x 6-1/8" .306 5,000 11" .75 CFI FLS16 1" x 6-1/8" .306 5,000 11" .75 Other sizes and galv available on request. No. Size Wire SWL Tension (lbs) Min. Edge Distance Wt (lbs) CFI FTS122 1/2" x 1-7/8" .223 1,200 6" 0.25 CFI FTS582 5/8" x 2-7/16" .306 2,500 7" 0.44 CFI FTS342 3/4" x 2-7/16" .306 2,650 6" 0.48 CFI FTS343 3/4" x 3-5/8" .306 4,500 9" 0.66 CFI FTS12 1" x 2-7/16" .306 3,080 6" 0.86 CFI FTS13 1" x 3-1/2" .375 4,500 8" 1.00 CFI FTS14 1" x 4-5/8" .306 6,500 11" 1.10 Other sizes and galv available on request. No. Size Wire SWL Tension (lbs) Min. Edge Distance Wt (lbs) CFI FOC34 3/4" x 4-5/8" .375 4,250 6" 0.55 CFI FOC1 1" x 5-5/8" .440 6,250 8" 1.20 CFI FOC114 1-1/4" x 7-5/8" .440 9,920 10" 3.20 Other sizes and galv available on request. Hot Dipped Galv CFI FOC34HDG 3/4" x 4-5/8" .375 4,250 6" 0.60 INSERTS - FERRULE INSERTS