|
 THREADBAR
DCR BAR
PUSH-FIT CONES
DYWIDAG TAPER TIE
WELDED ANGLE BRACKET
BATTER WASHER
CAST WING NUT
WING NUT BRACKET
WATERSEAL WASHER
CAST HEX NUT
EXPANSION ANCHOR
PLATE WASHER
COUPLER
Threadbar®
Threadbar is hot-rolled, high strength steel with two flat sides in the thread pattern that allow gripping and turning of the bars with a crescent wrench. The flat sides facilitate self-cleaning with each stripping operation. Threadbar® is bendable around a 6 diameter pin.
| No. |
Wt (lbs) |
Qty/Ctn |
| DS 34PF |
0.15 |
500 |
DCR Bar
The DCR is manufactured from high strength steel and fully threaded. DCR bar is considered more ductile than standard coil rod. DCR Bar is bendable around a 6 diameter pin and is also weldable allowing its use for welded waterstop. DCR bars provide a very economical solution for conventional and special tying/anchoring application. All hardware is interchangeable with thread bar.
| No. |
Size |
SWL Tension (lbs) |
Wt (lbs) |
| DSI 58DCR |
5/8" |
18,400 |
1.0 |
Push-Fit Cones
This spreader cone is used with 3/4", class 200 PVC pipe to allow 5/8" threaded rod to pass through the concrete untouched.
| No. |
Wt (lbs) |
Qty/Ctn |
| DS 34PF |
0.15 |
500 |
 
SWL provides a factor of safety of approximately 2 to 1.
DYWIDAG Taper Tie
Taper Ties employ one piece all steel tapering. This results in a stronger, much lighter system that uses the same size hardware at each end.
Welded Angle Bracket
Manufactured from high strength steel. Strengths are determined on full fillet welds along bracket. The threaded pin swivels up to ± 45°. The welded angle bracket is mainly used on H-piles below grade for one-sided forming applications. Masons assumes no liability for the welding connection. See technical bulletin for SWL reduction factor information.
|
No.
|
Size
|
|
DSI 58AB
|
5/8"
|
|
DSI 78AB
|
7/8"
|
|
Rod Diameter
|
A
|
B
|
C
|
D
|
SWL Tension (lbs)
|
Wt (lbs)
|
|
in.
|
in.
|
in.
|
in.
|
in.
|
klps
|
lbs.
|
|
5/8
|
5.25
|
4
|
0.25
|
2
|
19.1
|
4.0
|
|
7/8
|
7
|
6
|
0.50
|
2
|
39.20
|
8.50
|
SWL provides a factor of safety of approximately 2 to 1.
Batter Washer
Used when walers are at an angle to the tips. Permits any angle from 90° to 45°. Maximum spacing between strongbacks should not exceed rod diameter plus 1/4".
|
No.
|
Rod Diameter
|
Size
|
Wt (lbs)
|
| DSI 58BW |
5/8" |
5" x 3-1/2" |
1.80 |
| DSI 78BW |
7/8" |
6" x 5-1/4" |
4.00 |
Cast Wing Nut
Fabricated from ductile steel. Fast threaded for quick assembly and stripping. Utilized when frequent removal and application of nut is required.
|
No.
|
Size
|
SWL Tension (lbs)
|
Wt (lbs)
|
| DSI 58WN |
5/8" |
19,100 |
0.60 |
| DSI 78WN |
7/8" |
39,200 |
1.00 |
Wing Nut Bracket
Fabricated from ductile steel. Wing nut and plate are together as one piece unit. Maximum spacing between strongbacks should not exceed rod diameter plus 1/4".
|
No.
|
Size
|
SWL Tension (lbs)
|
Wt (lbs)
|
| DSI 58WNB |
5/8" |
19,100 |
1.10 |
| DSI 78WNB |
7/8" |
39,200 |
2.80 |
Waterseal Washer
Neoprene Waterseal Washers may be installed on inside tie rods to help eliminate water seepage along the tie. Generally specified when ties are used to form water containment structures.
|
No.
|
Inside Tie Rod Diameter
|
| DSI 58WW |
5/8" |
| DSI 78WW |
7/8" |
RETURN TO TOP
Cast Hex Nut
|
No.
|
Size
|
SWL Tension (lbs)
|
Wt (lbs)
|
| DSI 58HN |
5/8" |
19,100 |
0.30 |
| DSI 78HN |
7/8" |
39,200 |
1.10 |
RETURN TO TOP
Expansion Anchor
Expansion anchors can be used with 5/8" THREADBAR®. These anchors are used in many applications including one sided forming off existing concrete or temporary tiedowns in existing slabs. The fast Dywidag thread pattern (2½ threads per inch) provides quick installation and stripping. Available in two bore hold diameters 1⅜" and 1½", simply determine the estimated compressive strength of existing concrete and the depth of the hole.
Safe Working Load Information available on request.
|
No.
|
Size
|
Wt (lbs)
|
| DSI 58EA |
5/8" |
1.00 |
RETURN TO TOP
Coupler
Provides an efficient and safe alternative to conventional forming of protruding DCR bar. Allows for fast stripping and works safely by completing the splice of a later time.
|
No.
|
Size
|
SWL Tension (lbs)
|
Wt (lbs)
|
| DSI 58C |
5/8" |
19,100 |
1.20 |
| DSI 78C |
7/8" |
39,200 |
2.50 |
[BACK TO TIEING/HANDSET]
RETURN TO TABLE OF CONTENTS
|
Forming + Accessories 
